Making a Four-Pronged Spear

After making a simple spear I decided I would give a try at making a four-pronged hunting spear. Since this project is so similar to a previous post I will move through some of the steps more quickly. Anyone who is interested in more detail should see my previous post Making a Simple Spear.

First, I selected this small tree and chopped it down with my limestone axe head.

Screen Shot 2016-04-26 at 4.56.11 PM.png
The thin tree in the center

After this, I peeled the bark off one end and began working to split that end into four tongs. I did this by using a very thin stone flake and hammering it into the end with a stick. Once the flake was lodged all the way in and the split was running a few inches down the shaft, I used another stone flake to create a perpendicular split.

Screen Shot 2016-04-26 at 4.55.45 PM.png

I pulled the stone shards out then used fresh pine twigs and pulled them down so the shaft split several more inches and the points flared out more. I used pine because it bends easily and, therefore, the pressure of pulling the twigs down the grain of a much larger stick didn’t break them.

Screen Shot 2016-04-26 at 4.54.49 PM.png

Next, I sharpened the tips of the points with my obsidian knife until they were very sharp and cut the excess off the pine twigs. I left the pine twigs in because if I took them out the four prongs would come back together. The idea behind having a four-pronged spear is that it has more spread than a spear with a single point and, therefore, you have a better chance of getting the frog or fish you are aiming for.

Screen Shot 2016-04-26 at 4.53.52 PM.png

All I had to do after that was fire-harden it. Please see my previous post to see how fire hardening works. One interesting thing that happened this time is that some of the sap boiled out of the wood when I was hardening it. You can see the burnt sap bubbles in the picture below.

Screen Shot 2016-04-26 at 4.50.14 PM.png

Pictures of the finished project are below. I didn’t bother stripping all the bark off this time because it took forever last time and the bark on this stick is smoother so I don’t mind leaving it on.

Screen Shot 2016-04-26 at 4.51.48 PM.png

Screen Shot 2016-04-26 at 4.52.14 PM.png

Please leave a comment below if you have any questions and don’t forget to subscribe if you want to learn Stone Age technologies along with me!

Making Rope from Cattails

As I started planning out my next Stone Age projects it became increasingly clear that I needed to learn how to make rope, since so many Paleolithic technologies use cordage in some way. There are a plethora of different ways to make rope from natural materials, but I decided to make cattail rope first since there are tons of cattails where I live. Cattails are incredibly useful plants. The roots are an edible vegetable, several parts of the plant have antiseptic and medicinal properties, the seeds can be used to make fletching for darts or as tinder to start a fire, green leaves can be used to weave baskets, and dead leaves can be used to make rope.

The first step is to find a wetland area where there are cattails growing and gather some dead leaves. The leaves are brittle so you won’t need any tools to break them off, but they are a little tricky to break cleanly since there are so many fibers (these fibers are the reason cattails make good cordage). You’ll want quite a few leaves. If in doubt, take more.

Screen Shot 2016-04-27 at 11.52.38 PM.png

Screen Shot 2016-04-27 at 11.52.58 PM.png

Next, you need to soak the leaves for at least two hours, but not longer than four hours. They are very brittle at first, but soaking them will rehydrate the fibers and allow the leaves to be bent and twisted without breaking. Soaking for too long will cause the fibers to weaken and fall apart when twisted. Finding a place to soak them is easy since they always grow near water. If you’re not a Stone Age technology purist, you can use a sink or bucket.

Screen Shot 2016-04-27 at 11.51.28 PM.png
This only made about 10 inches of rope

After the leaves have soaked for the right amount of time you can begin to make your rope. The trickiest part of this whole project for me was figuring out how wet the leaves should be when you begin to twist them. They dry out fast so you need to take them out one at a time and leave the others soaking until you need them. However, the leaves can be too wet so sometimes I found I needed to press them flat to get some of the water out before I twisted them. The first step before you twist is to fold the leaf in half lengthwise as shown below.

13ande.gif

Then twist the until there is a kink. That will be the end of your rope. Fold the leaf in half where the kink formed and then begin to twist each of the two strands the opposite way from how you are braiding them together. That’s hard to explain in writing so please watch my short explanation video below to see it in action.

Here’s a picture of what it looked like before I had to add another cattail.

Screen Shot 2016-04-27 at 11.51.00 PM.png

…But when I needed to add the other leaves, which is done by twisting the end of one and the beginning of another together for about two braids, it looked like this.

Screen Shot 2016-04-27 at 11.50.30 PM.png

Not so pretty. I waited for it to dry a bit then used my trusty obsidian knife to cut off the pieces that were sticking out. My final product looks like this.

Screen Shot 2016-04-27 at 11.49.59 PM.png

It’s not pretty but the rope is pretty strong. I couldn’t pull it apart even when I tried, so I’d say it’s a success. This skill will be invaluable since rope is an essential part of many of the projects I intend to try and I’m very pleased with how well this process turned out.

13aoep.gif

Leave a comment if you have any questions and subscribe if you want to learn more about Stone Age technologies! Thanks for reading!

Making a Simple Spear

My first endeavors into Stone Age technology were some terribly failed attempts at making knives out of stone shards I gathered on vacation in the Appalachian mountains. I picked stones that were already thin and sharp, but they are pretty fragile and I was unable to make anything sharp enough to cut. I mostly scraped or chopped with them. I tried to make two different spears with them, but the stones kept breaking and they were unable to make a sharp point for the spear.

Screen Shot 2016-04-22 at 12.12.37 AM.png
Here they are in all their glory

Since these attempts were mostly unsuccessful I will not include the process here. The only one of these crude first attempts worth mentioning is this limestone fragment I found that works quite well as an axe. Since limestone is not a very tough material I hope to make a better axe soon, but for now I am using this:

Stone Axe.jpg

Clearly, I need a lot of practice before I’m able to make a knife capable of functioning, so I decided to cheat a little bit and use this obsidian knife I have.

IMG_0484.JPG

It is a genuine artifact from Central America that was found by a friend. I know it’s not exactly kosher to own historical artifacts, but this was found and brought back to the states by a well-meaning friend, so I keep it. It also hurts my archaeological sensibilities a little bit to use this, but since it’s a broken tool that was discarded by its original user, I like to think the original maker wouldn’t mind too much. If I could thank him or her I would. Eventually I will only use tools I make from scratch, but everyone has to start somewhere, including our Stone Age ancestors who certainly used tools that they did not personally make at times.

Making the Simple Spear

In order to make a spear that would be strong enough to withstand force and stay sharp for several uses, I had to chop down a hardwood tree and fire harden it. After a long time of searching for the perfect tree I settled on this small oak (at least I’m pretty sure it was an oak, but, since the leaves haven’t sprouted yet here in Michigan, it’s a bit hard to tell) and set to work.

IMG_0448.JPG
It’s the skinny straight one right in the center

I used my axe to hack away at the base and the top to get the straight, strong middle section I wanted. Once the axe had done its work I snapped and twisted the tree until I had the piece I wanted. The whole process took about 45 minutes and left my hands blistered and cramped.

Screen Shot 2016-04-22 at 12.38.12 AM.png
Starting to chop

 

Screen Shot 2016-04-22 at 12.42.03 AM.png
Taking a break

 

IMG_0470.JPG
At this point I thought ‘maybe I’ll just say I was making a quarterstaff instead.’

I used the axe to make a dull point on one end and then used the axe to help me peel off the bark. This process took an entire afternoon so I had to finish the next day. The next step in the morning was to use my obsidian knife to whittle the point into one that is very, very sharp. At this point my spear was basically done except for some fine-tuning.

Screen Shot 2016-04-22 at 12.26.29 AM.png

 

IMG_0479.JPG
These splintered and peeling bark fragments needed to be dealt with and whittling them down would have taken FOREVER with an obsidian knife, so I burned them off.

I could have used it right now, but the point would be dull after only one use so I had to fire harden it. Fire hardening is a pretty simple process, but it takes a long time. You simply hold the object near the heat for at least an hour all while rotating it slowly. It will darken slightly but you don’t want it to burn! If it burns it turns to charcoal and that is much weaker than wood. Since the wood is green, basically the heat makes the sap left in the wood boil and steam so that it hardens into a resin that holds the fibers of the wood together very tightly. This makes the wood very strong and durable. Here’s my final product.

Screen Shot 2016-04-22 at 12.54.20 AM.png

People usually think of spears as having stone points, but those were much rarer than these simple spears. I may eventually make a more complex spear with a stone point, but this spear is strong and plenty sharp and will stay that way for a long time. Even into the Middle Ages spears like this were very commonly used.

It took me three tries to make a successful simple spear with Stone Age technology. It’s really amazing how much effort goes into even simple tasks like this when you have to use the tools our Stone Age ancestors used. If I had been able to use a metal axe and knife this would only have taken an hour or two, but instead it took two full afternoons.

I am working on several more projects right now and I will post them as I complete them. Future projects will get more and more complex with time and practice!